Search

In Stock

PureTrust Surface Swabs PTS200

Order No.: PTS200

It fits for Meizheng PureTrust Intelligent Fluorescence Detector(MF2000).

Product Name Surface Swab

【Specifications5 swabs/ bag, 10 bags/ box

【Principle】

ATP exists in living cells which degrades quickly after cells are broken. Therefore, the degree of contamination of the target subject can be evaluated by measuring the amount of ATP. ATP and recombinant luciferase can catalyze the oxidation of substrate D-fluorescein and emit fluorescence. The fluorescence intensity is linear with the amount of ATP in a certain range.

【Applicable Scope】 Surface of the target subject

【Kit Composition】

CompositionQuantity
Surface swab50 swabs
Instructions Instructions1 copy

Storage and Validity

2-8℃,store away from light, valid for 6 months.

Date of manufacture is shown on the external packing.

Detection Sensitivity10-15 mol

Applicable Instruments

PureTrust Intelligent Fluorescence Detector(MF2000)

Operation Procedure

  1. Take out theSurface Swab from 2-8 °C and equilibrate 10-20 minutes to room temperature.
  2. Open the package and take out the swabs.
  3. Swab the target surface for While swabbing, rotate the swab tip to get sufficient sample.
  4. Collect the sample from a 10 × 10 cm2 Press down the swab tip on the target surface atan angle of 30°- 45° and apply Z-shape. For the irregular subject surface, when the surface area is less than 10 × 10 cm2, enough area should be swabbed as far as possible, and this swabbing method should be used for each detection.
  5. Follow-up operations can be stopped if there is visible dirt on the surface of the target subject, or the swab tip is obviously colored after swabbing.
  6. If the surface is wet with liquid, to avoid dilutingthe reagent, swab the target surface after its liquid slightly dried (no need extremely dry).
  7. If the sample is liquid, a drop of sample (about 20μL) can be absorbed by the cotton swab for detection (do not swabor dip the liquid directly).
  8. After sampling, reinsertthe swab back into the swab tube.
  9. Press the handle topierce the aluminum foil until the handle is fully inserted (the duration from sampling completion to piercing the aluminum foil should not exceed 15 minutes). Gently shake the swab tube side to side for 5-10 seconds (do not shake the swab tube up and down), and then wait for 30-60 seconds (prolong the reaction time properly if room temperature is quite low). Insert the swab into the luminometer for detection and read the reaction time properly if room temperature is quite low). Insert the swab into the luminometer for detection and read the result.

Precautions

  1. Read the instructions carefully before operating.
  2. The Surface Swab is only compatible with PureTrust Intelligent Fluorescence Detector (MF2000).
  3. Wear a pairof disposable gloves during the operation to avoid the contamination of exogenous ATP.
  4. The swab cannotbe kept under the light nor at room temperature for a long time after opening. Put the unused swabs back into aluminum foil bags and seal the bags. Stored the swabs away from light at 2-8 °C.
  5. After removing the swab, observe it firstly tocheck for the damage and leakage. If there is any damage or leakage, do not use the swab.
  6. Do not use the swab if the cotton is too dry.
  7. Do not touch the cotton swab during sampling. Do not touch the reaction cup at the bottom of the swab throughout the operation to avoid the inaccurate results.
  8. The intelligent fluorescence detector should be placed vertically above 60 degrees during testing process, or it may affect the result. Do not detect under strong light (strong light may increase the test value).
  9. Avoid contamination of reagent or sampling process or may cause inaccurate results.
  10. Proper disposalof the waste during the experiment is required.

Bestsellers

Aflatoxin B1 Quantitative Rapid Lateral Flow Test Kit

The kit is a lateral flow immunochromatographic assay that determines a quantitative level for the presence of aflatoxin B1 and is intended for use in nuts, grain and feed. This method is suitable for the rapid on-site test.Brochure-Grains & Feed Test. PDFMeizheng Bio-Tech Company Overview. PDF

Aflatoxin M1 Immunoaffinity Column

Order No.: QC0068,QC0069,QC0131,QC0071Column Capacity:100 ngVolumn: 3mLPackage: 25/50T 

Neomycin/Paromomycin, Kanamycin, Gentamicin and Spectinomycin Milk Comb Rapid Test Kit

The Neomycin/Paromomycin, Kanamycin, Gentamicin and Spectinomycin Rapid Test Kit is a lateral flow assay that determines a qualitative level for the presence of neomycin/ paromomycin, kanamycin, gentamicin and spectinomycin antibiotic residues in raw cow’s milk.Brochure-Dairy Test. PDFMeizheng Bio-Tech Company Overview. PDF

Immunoaffinity Column for 2-in-1 Aflatoxins (B1,B2,G1,G2) and Ochratoxin A

The immunoaffinity column can selectively adsorb aflatoxin (B1, B2, G1, G2) and Ochratoxin A from the sample solution, thereby having a highly targeted purification effect on the sample. The sample  solution that has been purified by passing through the affinity column can be directly used for HPLC analysis or for LC-MS/MS analysis after concentrating with nitrogen gas and resuspended.Order No.: HCM3725B/HCM3750BProduct Properties: AFT B1/B2/G1/G2 300ng, OTA 100ngSpecifications: 3mL,25T/50T

Milk Antibiotic Quinolones Rapid Test Kit

The Quinolones Rapid Test Kit is a lateral flow assay that determines a qualitative level for the presence of Quinolones antibiotic residues in raw cow’s milk.Brochure-Dairy Test. PDFMeizheng Bio-Tech Company Overview. PDF

Beta-lactams, Tetracyclines, Streptomycin, Chloramphenicol and Cefalexin Comb Milk Rapid Test Kit

The Beta-lactams, Tetracyclines, Streptomycin, Chloramphenicol and Cefalexin Rapid Test Kit, 5-in-1 Combo Rapid Test Kit is a Lateral Flow assay that determines the residues for the presence of target antibiotic residues in raw milk.Brochure-Dairy Test. PDFMeizheng Bio-Tech Company Overview. PDF

Milk Aflatoxin M1 Lateral Flow Rapid Test Kit

Aflatoxin M1 Rapid Test Kit is a lateral flow assay that determines a qualitative level for the presence of aflatoxin M1 in raw cow’s milk. This test is designed for rapid field use or daily control in laboratories.Brochure-Dairy Test. PDFMeizheng Bio-Tech Company Overview. PDF

 

Back to Top
Product has been added to your cart